1984-1989 Toyota MR2 AW11 Visor Passenger RH side grey gray fabric
EUR 14,85
Alle objecten
Over
Alle feedback (352)
lx-parts (1865)- Feedback gegeven door koper.
Afgelopen maand
Geverifieerde aankoop
Quick response and fast payment. Perfect! THANKS!!
autoparts-factory (18097)- Feedback gegeven door koper.
Afgelopen maand
Geverifieerde aankoop
Hope to deal with you again. Thank you.
metalspacersonline (3142)- Feedback gegeven door koper.
Afgelopen 6 maanden
Geverifieerde aankoop
Great communication. A pleasure to do business with.
keyron999 (10662)- Feedback gegeven door koper.
Afgelopen 6 maanden
Geverifieerde aankoop
Thank you for an easy, pleasant transaction. Excellent buyer. A++++++.
keyron999 (10662)- Feedback gegeven door koper.
Afgelopen 6 maanden
Geverifieerde aankoop
Hope to deal with you again. Thank you.
regan0331 (37988)- Feedback gegeven door koper.
Afgelopen 6 maanden
Geverifieerde aankoop
Hope to deal with you again. Thank you.
Recensies (5)
26 jan 2021
Sub-par to OEM Honda quality but still overall great value! Does the job of holding fairings in place! Stainless fasteners are super shiny too!
Pros is it's much cheaper than the actual Honda 90111-KW3-003 Rubber Well Nuts. Cons is the actual size are much smaller than the actual Honda 90111-KW3-003 Rubber Well Nuts. How? The rubber flat washer diameter (let's call this front of well nut) is much smaller, where the stainless bolts begin threading into. The well nut still does the job of flaring up the rubber cylindrical portion (let's call this rear of well nut) to hold the fairings in the place. Due to the front portion being smaller it provides less protection, or the potential for more rubbing, between the fairings when fastened. Would I recommend it? Is it good value? Is good quality? Yes, yes, and (kinda) yes. If money's not an issue I would've gone with the actual Honda 90111-KW3-003 Well nuts, in which I will in the future proceeding forward. Another Pros is this package came with stainless fasteners. The flange portion of the fasteners are also smaller than the stock Honda fasteners. Overall it is still a great deal. If you're looking for OEM Honda quality, this is not it.
01 jun 2016
KONI Sport 8610-1365S on a 1990 Corolla GT-S
I have tried quite a few coilover setups from KSport to MRPs on my vehicle. But I must say that Koni Sport yellow strut inserts are on another level. They provide near perfect dampening for the streets to offroad rallycross. I have tested these struts on gravel and on a frozen lake. The gravel rallycross was at Snoqualmie's DirtFish Rally School compound and they were able to hold their own with just enough body roll at about 1/3 or 1/4 soft settings. Mind you my springs are of H&R Sport Spring setup with strut spacers on top to heighten back to neat stock ride height. Up in Canada I was at Barnes Lake for an ice rallycross event setup at the most softest setting. Weight transfer on the Koni's is very predictable even on next to no friction surface. Highly recommend these any for any car enthusiast!
13 feb 2020
Honda NOS CBR600, 2001, Rear Mark (Type 1), # 77217-MBW-A10ZA S-137
Legit OEM Honda product. I bought this for my rear tail section of my 2001 Honda CBR600 F4i and it matches. Sticker seems to be of the same size and quality as the one on my tail section. If anybody intends to repair, repaint, and re-vinyl (or simply restore) the whole rear tail section this is a must get item!